Electrolyser Cell Testing - DILICO Hydrogen Cell Test System for PEM and AEM Electrolysers

  • Reliable MEA testing for the next generation of PEM and AEM electrolysers
  • Quick membrane changes at the integrated cell holder
  • “Ready to use" electrolyser cell testing system (insert the membrane, close the cell holder, start the software and begin the measurement)
  • Lifetime analysis of the MEA with DILICO CURR TEMP for baltic quickCONNECTFixture FC25 for measuring the current density and temperature distribution as well as connection for distributed electrochemical impedance spectroscopy (EIS)
  • Ideal for analysing individual cell components such as bipolar plates (material and flow field design), membrane electrode assemblies and for definition of compression parameters of the cell

Add to compare

Electrolyser Cell Testing - DILICO Hydrogen Cell Test System for PEM and AEM Electrolysers

  • Easy handling characterises DILICO Hydrogen Cell Test System
  • Basis for the rapid membrane integration is the proven baltic quickCONNECTfixture system
  • With compressed air, the compression force on the active cell surface can be variably adjusted, which is an important parameter for the operation of electrolysis membranes
  • The cell can be actively preheated or cooled before and during operation in this electrolyser cell testing equipment
  • The DI water supply has conductivity measurement and preheating for an optimal electrolysis process
  • The gases produced, hydrogen and oxygen, are dried, the flow rates measured and the proportions in the respective gas stream determined
  • Test sequences, such as the time recording of current and voltage characteristics and other parameters, can be programmed in the software in a script and thus enable reproducible measurements to be carried out
  • DILICO CURR TEMP for baltic quickCONNECTFixture FC25 consists of a segmented sensor layer with integrated 64 current and 64 temperature sensors, electronics for evaluating the measured data, and software for visualization and extensive evaluation of the measured values for current density (current strength related to area) and temperature
  • The sensor layer can also be provided with a connection to create an interface for measuring electrochemical impedance spectroscopy (EIS) and to carry out parallel EIS measurements on selected segments

Key features

  • Standardised DILICO Hydrogen Cell Test System for PEM and AEM electrolysers for very simple and fast integration of membranes and bipolar plates
  • The test stand is equipped with a complete measuring cell and is therefore ready to use
  • User-friendly software allows a very short training period
  • Membrane areas: 25 cm ²
  • Controllable power source: Selectable up to 125 A or 250 A
  • DI water preheating / conductivity measurement: up to 80 °C / yes
  • Pressure and temperature measurement: at all inputs and outputs
  • Gas drying: hydrogen and oxygen
  • Compression force on active cell surface: adjustable by compressed air supply
  • Compressed air measurement for H2, O2 and DI water: yes
  • Customer-side connections: DI water, water drain, electrical connection, gas extraction, compressed air, nitrogen

Application areas

  • Analysing membranes, bipolar plates and determining contact pressures
  • Performing long-term tests with varying operating parameters
  • Comparison of different versions of individual cell components for the next stack generation
  • Pre-series qualification of materials and operating procedures
  • Testing run-in procedures for quality inspection

Use cases

  • DILICO Hydrogen Cell Test System is used by MEA manufacturers to compare different MEA versions, minimise run-in procedures and identify suitable samples for long-term testing
  • Suppliers of bipolar plates who want to know how well their bipolar plates perform in electrolyser operation
  • Ideal for research institutions that compare different MEAs and operating strategies and require relevant data for modelling

Contact us

  • DILICO has the right electrolyser cell testing for you. Fill out the contact vendor form to contact the vendor.
Brand DILICO
Type of Electrolyser PEM/AEM
Max Pressure (in bar) 8
Min Pressure (in bar) 1
Max Power (in kW) 1
Max Input Voltage (in V) 10
Max Current (in A) 250
Manufacturing Readiness (MRL) 9
Technology Readiness (TRL) 8
Max Medium Temperature (in °C) 80
Min Medium Temperature (in °C) 20
DiLiCo engineering GmbH

DiLiCo engineering develops and produces measurement technology for monitoring and analysing electrolysis cells, fuel cells, redox flow batteries and batteries. This includes cell voltage monitoring and contacting solutions for cell voltage pick-up, in-situ current and temperature distribution measurements as well as EIS measurements for ageing analysis and evaluation of operational management. Electrolysis test stands for the reproducible measurement and analysis of electrolysis single cells are another of DiLiCo's areas of expertise.

Fill out the form and let us do the heavy lifting. Your inquiry will be sent to the right person within the vendor organization. No strings attached. We will help you to get an answer.

Latest products

Browse the Hyfindr Digital Ecosystem

Suppliers icon
Hyfindr
B2B Suppliers
Forum icon
Hyfindr
Tech Videos
Assignment icon
Hyfindr
Tech Knowledge
Thumb up icon
Hyfindr
Tech Advisory
Group icon
Hyfindr
Tech Community